Pull Type Archives - The Linear Motion Blogger

Motion Control – Select from the S-70-300H Series of 3 Inch Dia. Push Type Solenoids to Meet the High Force Requirements of an Application!

September 10, 2024 Editor

Motion Control – Push Type Solenoids

Motion Control – Van Nuys, CA – Solenoids – The S-70-300H Series of high force Push Type Tubular Solenoids has been released by Magnetic Sensor Systems (MSS). Ideal for strokes of up to 4.00 inches, this series of solenoids features 18 different solenoids to select from based on the Force, Voltage, Duty Cycle, and Stroke requirement of the user. MSS Solenoids coils typically utilize Class “F” 23 to 40 AWG (American Wire Gauge) windings with Class “A” lead wire insulation for better protection of the solenoid during longer duty cycles.

The S-70-300H Series of solenoids feature a 3.000 in. diameter x 7.00 in. long housing and a 1.75-12 UN A thread for mounting.

Motion Control – The S-63-38 Series of 0.38 Inch Dia. Pull Type Solenoids Features 16 Standard models to Meet Voltage, Duty Cycle, Force, and Stroke Requirements of an Application!

July 30, 2024 Editor

Motion Control Technology Newsletter – Tubular Solenoids

motion control - solenoid
Motion Control Technology – Van Nuys, CA – The S-63-38 Series of Pull Type Tubular Solenoids has been released by Magnetic Sensor Systems (MSS). This series of 0.38 in. diameter solenoids features 16 standard off-the-shelf solenoids to select from based on the Voltage, Duty Cycle, Force and Stroke requirement of the user.

These miniature solenoids featuring a 0.38 in. diameter have a 0.66 in. long housing and when retracted are just 0.80 in. long.

Motion Control – Open Frame Series of 18 Pull Type Solenoids with a 1 Inch Stroke Can Meet the Voltage, Duty Cycle, and Force Requirements of Many Applications!

July 02, 2024 Editor

Motion Control – Open Frame Solenoids

Motion Control – Van Nuys, CA – The S-18-100 Series of Open Frame Pull Type Solenoids from Magnetic Sensor Systems (MSS) includes 18 different solenoids to select from based on the Voltage, Duty Cycle, Attractive Force (up to 100 oz) and Stroke requirements of the user. MSS Solenoid coils typically utilize 23 to 40 AWG (American Wire Gauge) windings with Class “F” insulation for better protection of the solenoid during longer duty cycles.

The S-18-100 Series solenoids are 1.000 in. wide x 0.84 in. high x 1.74 long and have a 1.00 stroke. The noncaptive plunger or actuator is 0.312 in. in diameter with a clevis end for load attachment.

Motion Control – Select from a Series of Compact Electromagnets to Meet Holding Force and Duty Cycle Requirements of an Application!

May 21, 2024 Editor

Motion Control – Electromagnets

Version 1.0.0

Motion Control – Van Nuys, CA – A powerful series of compact, low cost electromagnets has been released by Magnetic Sensor Systems (MSS). Their E-22-150 Series of Tubular Electromagnets 1.5 in. in diameter x 2.15 in. feature 19 different windings to select from based on the duty cycle and holding force requirements of the application. E-22-150 Electromagnets are immediately available off-the-shelf in sample quantities and OEM quantities for Just-In-Time deliveries.

Depending on the application, duty cycle, and required force, the electromagnets in this series can supply 54 to 83 lbs. of holding force for duty cycles ranging from 100% (continuously on) to 10%. This series of electromagnets is ideal for use for: Door controls (hold open, hold close), relays, lifting gantries, material handling, magnetic locks and switches, security systems, failsafe brakes, magnetic separation, research equipment, valves, and office equipment.

Motion Control – Select From the S-20-100X Series of 1 Inch Dia. Pull Type Solenoids to Meet Voltage, Duty Cycle, Force, and Stroke Requirements of an Application!

January 08, 2024 Editor

Motion Control – Tubular Solenoids

Motion Control – Van Nuys, CA – Magnetic Sensor Systems (MSS) has released their S-20-100X model of Pull Type Tubular Solenoids. Their S-20-100X series of solenoids features 18 different solenoids to select from based on the Voltage, Duty Cycle, Force and Stroke requirement of the user.

MSS Solenoids coils typically utilize Class “F” 23 to 40 AWG (American Wire Gauge) windings with Class “A” insulation for better protection of the solenoid during longer duty cycles.

Motion Control – NEW! Metric and Inch Dimensioned Electric Cylinders Feature High Speed, Zero Cogging, and 1.25 Micron Resolution

December 19, 2023 Editor

Motion Control – Electric Cylinders!

Van Nuys, CA – Motion Control – New, Metric and Imperial dimensioned Electric Cylinders or Linear Voice Coil Servo Actuators have been released by Moticont. The new, compact 25.4 mm (1.000 in.) stroke SDLM-025-095-01-01M and SDLM-025-095-01-01 Linear DC Servo Actuators feature high repeatability, high acceleration/deceleration, and zero cogging! These high force-to-size Electric Cylinders have linear encoders mounted internally for closed loop servo operation. Additionally, to operate at peak efficiency, integral temperature sensors provide data to achieve the highest possible throughputs.

The clean fully enclosed SDLM-025-095-01-01M and SDLM-025-095-01-01 Servo Actuators are 25.4 mm (1.000 in.) in diameter, the housing is 95.3 mm (3.750 in.) long and the total length of the housings and shafts are 139.7 mm (5.500 in.).

Motion Control – Select from a Series of Low-Profile Push/Pull Type Solenoids to Meet the Specific Voltage, Duty Cycle, and Force Requirements of Your Application!

October 31, 2023 Editor

Motion Control – Compact Push/Pull Solenoids

Motion Control – Van Nuys, CA –Magnetic Sensor Systems (MSS) has released 18 low-profile Push/Pull Clapper Solenoids with the ampere turns (windings) adjusted to meet the specific force and duty cycle requirements of an application. The S-66-100 Series of Low-Profile Clapper Push/Pull Type Solenoids from MSS are just 1.00 in. in diameter and 0.66 in. deep.

These compact solenoids have a 0.40 in. stroke and can be operated at a variety of duty cycles (voltage dependent) and are the ideal choice for: Medical dispensing, plotters, clutches, switches, mixing, valve control, vending machines, games, fire suppression systems, cabinet locks, door controls, and sorting equipment.

Motion Control – Tutorial – Solenoid Construction

February 26, 2023 Editor

Motion Control – Tutorial – Solenoid Construction

Solenoid Construction

A Solenoid is a long wire, wound with a helical pattern, usually surrounded by a steel frame, having a steel core inside the winding.

When carrying a current “i “, the Solenoid becomes an electro-mechanical device, in which electrical energy is converted into mechanical work.

Motion Control – Compact Rotary Solenoids Available in OEM Quantities, Can Be Performance Matched To An Application!

December 27, 2022 Editor

Motion Control – Rotary Solenoids

Motion Control – Van Nuys, CA –The R-09-150 CCWM Series of Counter Clockwise, Forward Shaft Extension Rotary Solenoids from Magnetic Sensor Systems (MSS), available in OEM quantities, features 18 different winding configurations allowing the user to match torque and duty cycle requirements to an application. These compact 38.1 mm (1.50 in.) diameter solenoids are just 22.098 (22.1) mm (0.87 in.) long and have two M4X0.7 threaded studs (8-32 studs optional) 7.366 (7.4) mm (0.29 in.) long on a 22.225 (22.2) mm (0.875 in.) bolt circle. The shaft has 40 degrees of counter clockwise rotation, extending (13.0) mm (0.51 in.). The shaft end is serrated for a better grip of the attached load.

The R-09-150 CCWM Series of Rotary Solenoids can be specified with a choice of AWG winding of 21 to 37 gauge. Specifying a different AWG for the windings allows the user to control the performance of a solenoid with respect to duty cycle, current supplied, and torque by controlling the ampere turns.

Category Archives: Pull Type

Motion Control – Select from the S-70-300H Series of 3 Inch Dia. Push Type Solenoids to Meet the High Force Requirements of an Application!

Motion Control – Push Type Solenoids

Motion Control – The S-63-38 Series of 0.38 Inch Dia. Pull Type Solenoids Features 16 Standard models to Meet Voltage, Duty Cycle, Force, and Stroke Requirements of an Application!

Motion Control Technology Newsletter – Tubular Solenoids

Motion Control – Open Frame Series of 18 Pull Type Solenoids with a 1 Inch Stroke Can Meet the Voltage, Duty Cycle, and Force Requirements of Many Applications!

Motion Control – Open Frame Solenoids

Motion Control – Select from a Series of Compact Electromagnets to Meet Holding Force and Duty Cycle Requirements of an Application!

Motion Control – Electromagnets

Motion Control – Select From the S-20-100X Series of 1 Inch Dia. Pull Type Solenoids to Meet Voltage, Duty Cycle, Force, and Stroke Requirements of an Application!

Motion Control – Tubular Solenoids

Motion Control – NEW! Metric and Inch Dimensioned Electric Cylinders Feature High Speed, Zero Cogging, and 1.25 Micron Resolution

Motion Control – Electric Cylinders!

Motion Control – Select from a Series of Low-Profile Push/Pull Type Solenoids to Meet the Specific Voltage, Duty Cycle, and Force Requirements of Your Application!

Motion Control – Compact Push/Pull Solenoids

Motion Control – Tutorial – Solenoid Construction

Motion Control – Tutorial – Solenoid Construction

Solenoid Construction

Motion Control – Compact Rotary Solenoids Available in OEM Quantities, Can Be Performance Matched To An Application!

Motion Control – Rotary Solenoids

Recent Posts

Catagories